JBradleybz Posted April 5, 2013 Share Posted April 5, 2013 Just a quick thank you John for a couple more jobs that you've done for us this week. As always.........an excellent and friendly service supplied. It's so nice to have somebody that you can rely on 100%. Thank you very much for a kind recommendation glad your happy with our services, we are always here to help you thanks jon at JB Heating Services. Link to comment Share on other sites More sharing options...
FeFeFace Posted April 9, 2013 Share Posted April 9, 2013 Thanks to those that gave me advice, ive managed to get it fixed :-) thank you Link to comment Share on other sites More sharing options...
SaintDuncan Posted April 10, 2013 Share Posted April 10, 2013 Ok I have a year old Baxi Neta-tec that is working fine for heating and hot water but the LCD is flashing indicating the temperature and a few seconds later the display changes to indicate a bar reading which fluctuates between 0.6 and 0.9. When the heating is turned on the LCD indicator flashes the temperature and then intermittently flashes 5d. I believe this indicates an annual service is due but the bar reading is what is concerning me. Any ideas? Link to comment Share on other sites More sharing options...
JBradleybz Posted April 11, 2013 Share Posted April 11, 2013 Top the water pressure up to about 1.3 bar and see if it continues. Otherwise have it checked at the same time as a service that way your getting more for your money by doing two jobs at same time. Cheers jon at JB Heating Services. Link to comment Share on other sites More sharing options...
jackwillroar Posted April 20, 2013 Share Posted April 20, 2013 Ive just used Sam for a hot water tank move, great job ---------- Post added 20-04-2013 at 10:51 ---------- Ive just used Sam for a hot water tank move, great job Sam Lovatt, 07909842848, great heating an plumbing engineer, i recceomend Link to comment Share on other sites More sharing options...
picasso303 Posted April 21, 2013 Share Posted April 21, 2013 Hoping someone can help. We have an Ideal Logic + Combi Boiler and since yesterday we have had no hot water, and no heating either. The LCD says "Low Pressure" and fill to 1 Bar but it is already at 2 Bar. So I am not sure if the low pressure message is right. If we open the blue and black taps like we have been shown before then will we simply be increasing the pressure? Help:help:! Link to comment Share on other sites More sharing options...
sawheating Posted April 21, 2013 Share Posted April 21, 2013 Try the reset button first. The pressure gauge may be wrong if it is blocked. Please call if your still stuck and I can go over it on the phone now if you require Scott Link to comment Share on other sites More sharing options...
Leeman Posted April 21, 2013 Share Posted April 21, 2013 Scott's spot on, had a few of these sticking now. Normally incresing the pressure cures it but then you need to bring the pressure back down by bleeding a radiator or drain off till itss back down to 1.5 bar max. Hope you get it sortted. Link to comment Share on other sites More sharing options...
Nagel Posted April 23, 2013 Share Posted April 23, 2013 I'm looking for someone to replace my old boiler with an Intergas one. Message me if you're certified by Intergas to fit their boilers and you're interested in the work. Link to comment Share on other sites More sharing options...
JBradleybz Posted April 23, 2013 Share Posted April 23, 2013 I would rather have the Ideal Logic plus but thats my opinion, interested to know why you would like the intergas i looked into one for a customer last year and to be honest i thought it was not that great. Do they stipulate it has to be one of there registered certified engineers as when i asked them last year they said any gas safe engineer could fit one. Link to comment Share on other sites More sharing options...
Recommended Posts